Shopping Cart
Quantity in Cart: 0 - $0.00

POWERBOX PROFESSIONAL

$274.95

PowerBox Professional

The PowerBox Professional has been a popular and reliable power supply system ever since its introduction in 2002 however, until now, it has been limited to use with 4S or 5S NiCd or NiMH batteries. Now we are introducing the 3rd generation of the PowerBox Professional which has been completely revised to cater for the developing demands on modern power supply systems.

The new version incorporates many new features including a high-resolution OLED screen, electronic switches, menu-based programming, regulated output voltage of 5.9 V or 7.4 V, four match-channels, telemetry capability and much more.

The Professional supports eight channels remotely accessed from the receiver, four of which are equipped with a servo-match function. This makes it ideal for aerobatic models in the 25% to 35% class as well as for jets. The purpose of servo-matching is to adjust the centre point, end-points and direction of rotation very accurately for each servo. This means that multiple servos connected mechanically to a single control surface can be fine-tuned to operate exactly in parallel preventing the servos working against each other. They are able to develop their full power and consume less current. Servo-matching can also extend the effective life of your servos enormously.                          

However, servo-matching also allows functions to be linked avoiding the need for two channels at the transmitter. As an example: the left and right landing flaps can be operated using just one transmitter channel as the direction of rotation and the servo end-points are adjusted at the Professional. This saves channels and in many cases makes the transmitter programming procedure much easier.

All the settings are programmed using the SensorSwitch in conjunction with the high-resolution OLED screen. All the menu points are displayed in full text form on the screen - rather than as abbreviations - which makes it much easier to understand the procedure.

Naturally it is possible to use the MagSensor to switch the Professional on and off if you wish to conceal the switch.

The PowerBox Professional can be updated using the USB interface adapter. This means that future expansions - such as additional telemetry systems - can be loaded and used in just a few minutes.

Features:

        Servo-Match function: servo centre, end-points and reverse for 4 channels and 8 servos
        Graphic OLED screen with 128 x 64 pixels
        Extremely user-friendly menu-based programming using the SensorSwitch
        8 channels
        Signal amplification and interference suppression for all 12 outputs
        Variable frame rate, range 9ms – 21ms
        16-bit processor for fast, high-resolution signal processing
        Double-regulated output voltages for receivers and servos
        Regulated voltage with selection facility, 5.9V or 7.4V
        Connection facilities for Spektrum, HoTT and Multiplex MSB downlink bus systems
        Direct transmission of battery voltage and capacity to the transmitter
        Separate voltage and capacity display for each battery
        Minimum value memory alerts the user to voltage collapses
        Large-area heat-sinks for high regulator performance
        Regulator monitoring, regulator error indicator
        Support for three battery types: LiPo, NiMH / NiCd, LiFePo
        Suppression of any servo feedback currents which may occur
        Updateable with PowerBox Systems USB Interface connectors

Technical Data:

    Operating voltage            4.0V - 9.0V
    Power supply      2S LiPo, 2S LiFePo, 5S NiCd/NiMH
    Current drain Power-on state       130mA
    Current drain Standby      15µA
    Maximum load current    Peak 2x20A
    Drop-out voltage              0.3V
    Output voltage   5.9V and/or 7.4V regulated
    Channels              8
    Servo sockets     12
    Programmable servo outputs       4 channels, 8 servos
    Servo signal resolution    0.5µs
    Signal frame rate              9ms, 12ms, 15ms, 18ms, 21ms
    Screen   OLED 128 x 64 pixels, graphic
    Supported telemetry systems       Spektrum, HoTT, M-Link
    Dimensions         110 x 72 x 24 mm
    Weight 115g
    Weight Sensor Switch      15g
    Temperature range          -30°C to +75°C


Sold Out
  • Model: V-PB-4330
  • Manufactured by: PowerBox


Copyright © 2017 BVMJets.com. Powered by Zen Cart – Hosted by <ixwebhosting.com>
Back to top