English
Categories
- PNP/Go Fly Accessories
- Kit Accessories
- HSD Jets
- Skymaster Accessories
- PowerBox
- Carbon Fiber
- Air Systems
- Accessories
- Installation Organizers
- Building Materials
- Finishing Materials
- Adhesives
- Electric VioFan (EVF)
- Chargers / Power Supplies
- Electric Accessories
- Batteries
- Turbine Mounts & Straps
- Turbine Accessories
- Fuel Cells
- Fuel System Accessories
- Jersey Modeler
- Cockpits
- Lubricants
- PermaGrit
- Tools
- Radio Gear
- Pilots
- Landing Gear
- Wheels Tires and Brakes
- Jet Cases / Cradles
- Specials
- Apparel and Gifts
- Books
- Gift Certificates
- Penn Bags
Canopy Hook Shims
Machine cut from .015" Poly Ply These shims can be used to reinforce the fiberglass flanges on the hatch shelf. If the slot is a bit oversize, position the shim for the best hatch-to-fuse fit and then glue (Zap-A-Gap) it under the flange. Of course, scuff the mating surfaces with #80 grit sandpaper for best adhesion. Make final adjustments with a small PermaGrit flat file. Perfect the Canopy Hook-to-slot fit one at a time.
$6.95
EZ Pylons Kit (pair)
For All Bandits, Electras, 63" Sabres or similar Jet Models. BVM EZ Pylons allows quick attachment and release of external stores without the use of tools. Simply hand operate the bolt head trigger on the side of the pylon. The EZ Drop also allows the release of the stores remotely. Comprehensive manual and drawings are included. This pair of pylons requires the use of either (2) BVM EZ Hanger (BVM#2185) or (2) BVM EZ Drop (BVM#2187) to mount the appropriate wing tanks or ordnance.
$55.00
Fuel Vent Plug
Remove Before Flight. Handling your Kerosene powered model is a lot less messy if you plug off the fuel system overflow vent. You prevent the stinky spills in your vehicle and workshop. But, if you take-off with the vent still plugged, your engine will starve for fuel and flame out, usually one or two minutes into the flight. Unfortunately, this has happened to two customers recently. BVM's "Remove Before Flight" Vent Plug solves the problem. It would be hard to taxi out and not see the Red Flag dragging on the ground.
$11.99
Pump Mount 2/PK
The BVM Pump Mount can be used to secure most standard turbine fuel pumps or smoke pumps. The plastic mounts are adhesive backed. Additional screws may be used to secure the mount to the surface. Two 8" zip ties are included. Two mounts per package.
$5.95
Wire/Tubing Loom
Braided loom neatly organizes your servo wires and pneumatic tubing. Use in conjunction with the BVM O-Clips (BVM# PA-SR-0026)
$8.95
BVM Cougar Jet-Foam Cradle
The Jet-Foam Cradle for the BVM Cougar is designed to allow you to work on the model right side up or upside down, exercise the landing gear and flaps, with or without the vertical fin attached. The Cradle can be used on the ground or on a portable 30" high table. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$165.00
General Purpose Jet-Foam Cradle
Originally developed for the BVM 84" Sabre Jet, this Jet-Foam Cradle works well for many medium size jets such as the Bandit, Electra, MiG-15, and F-100. The distance between the End Brackets can be adjusted on the PVC Tubes and the Velcro Straps will hold the model for field assembly, disassembly, and transport, as well as being very handy in the shop while you work on the model. Review the accompanying enclosures and the photos below to see the advantages a BVM Jet-Foam Cradle offers. Modify as desired A razor saw or sharp knife can be used to put a "V" notch in an End Bracket if that best suits your model. Outline the desired modification with tape, then cut. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$155.00
O-Clips
| There are a number of devices on the R/C
market that help organize the installation of electronic and
pneumatic lines in your model. The "O-Clips" system will add a
new dimension to the task.  The "O-Clip" system is non-specific in regards to tubing diameter or wire size and allows grouping these components together where it is convenient,  Each package contains four each of three different sizes of "O-Clips", the appropriate size "O" rings (a few extra of each) and two rolled strips of 1/64" x 1/2" x 12" plywood. This group of 12 is sufficient for most medium to large size models. |
Ultra Bandit Jet-Foam Cradle
The Ultra Bandit Jet-Foam Cradle is the largest in BVM's line of airframe handling products. The PVC tubes are longer (38") and the forward End Bracket is wider to carefully handle the inlet ducts without damage. For lots of handling, building, and transporting conveniences, the Ultra Bandit fuselage aft section is removable. This special Jet-Foam Cradle allows support of the front half (with the aft fuse section removed) to allow engine access, fuel tanks, etc. NOTE: Extra lengths (12 feet) of the 1-1/2 wide Velcro straps (BVM # PA-SR-0079) are available to assist in mounting the Jet Foam Cradle to a trailer shelf or floor for safe and soft transport. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$155.00
#2 X 3/16" Button Head Panel Screws 30pk
#2 X 3/16 Button Head Panel Screws 30pk Jets, WWII models and even scale helicopters sometimes require removable panels that yield access to servos and other components. Jets also have other special requirements, such as attaching thin fiberglass parts. The socket head panel screws (SHPS) from BVM may be just what's needed to accomplish the task and have the finished product look great. The very small dome shaped head with its .050 hex socket and black finish will appear very scale-like in most applications. The 3/8 long self-tap screw thread is just right for attaching thin fiberglass panels made from BVM's Poly Ply materials. DISCLAIMER: Occasionally our supplier substitutes silver screws for black. If you prefer to have only black screws, please note this when placing online or phone orders.
$6.50
3/8" Long Button Head Panel Screws 25pk
3/8 Long Button Head Panel Screws 25pk Jets, WWII models and even scale helicopters sometimes require removable panels that yield access to servos and other components. Jets also have other special requirements, such as attaching thin fiberglass parts. The socket head panel screws (SHPS) from BVM may be just what's needed to accomplish the task and have the finished product look great. The very small (5/32 dia) dome shaped head with its .050 hex socket and black finish will appear very scale-like in most applications. The 5/32 long or 3/8 long self-tap screw thread is just right for attaching thin fiberglass panels made from BVM's Poly Ply materials. DISCLAIMER: Occasionally our supplier substitutes silver screws for black. If you prefer to have only black screws, please note this when placing online or phone orders.
$7.50
EZ Drop
AIR OPERATED - SPRING RETURN BVM EZ-DROP simplifies the mounting and releasing of external stores without using a dedicated radio channel or servos. It operates via a single air line from the models retract system. Simply use the snap roll button to command a slight over travel on the retract system valve, and the tanks or bombs release instantly.
$39.95
EZ Hanger
To compliment our pneumatic powered EZ-DROP, we also offer this similar device intended to ease the mounting and removal of external stores by simply pulling aft on the cable. Tanks, bombs and missiles really add to the "presence" and "scale realism" of jet models whether they be on static display or in action at 150 + m.p.h. Handling and transporting the model with external stores however, can be a cumbersome task and sometimes results in damage to fins or pylons. We think you will find the BVM EZ-Hangers a very handy accessory when adding some "parasites" to your jet. EZ-Hangers fit into the same size opening and utilize the same bolt pattern as the EZ-DROPS, they are interchangeable.
$25.95
Poly Ply .010" - 2pk
Poly Ply .010" - 2pk
Poly Ply .015" - 2pk
Poly Ply .015" - 2pk
Poly Ply .020" - 2pk
Poly Ply .020" - 2pk
Poly Ply assorted pack (1 sheet of each .010", .015" and .020")
Poly Ply assorted pack (1 sheet of each .010", .015" and .020")
Milled Fiber 4oz
Milled Fiber 4oz
To strengthen glue joints.
These 1/32" long fiberglass fibers will add strength to an epoxy glue joint. Milled fiber also thickens the glue mix so it will stay where you put it.
A combination of some milled fiber with microballoons and resin will also yield a stronger fillet material.
Pin Hole Filler 6oz
Pin Hole Filler 6oz
Sabre Decals (set of 5)
Sabre Jet Decals sized to fit the BVM 60", 63", F-86 These are freshly made waterslide decals (set of 5 sheets) that utilize the latest techniques and materials. The quality is superb. This set of 5 sheets will authentically adorn your F-86.
$75.00Bestsellers
Manufacturers
Specials [more]
HSDJETS T-33 Foam Turbine Thunderbirds Colors PNP XT60 plug
Save: 18% off
"Dry Lube" 2 for $10.00
Save: 9% off
