Use For All Mechanical Mating Parts Metal To Metal - Metal To Plastic Its light viscosity allows it to penetrate quickly and lubricate from within. Its formulation of high quality waxes and PTFE promote friction free operation. Its liquid carrier evaporates and leaves the friction relieving chemistry. It guards against rust and corrosion and it does not attract dirt. Especially good for electronically driven retractable landing gear and mechanical moving parts of pneumatic gear. CAUTON: DO NOT apply to pneumatic cylinders.
$5.50 $4.40Velcro / Black adhesive backed 3/4 X 36 Very convenient to mount EVF power batteries. Works similar to the white adhesive product #PA-SR-0083 but is sometimes more convenient to cut, peel, and stick.
$13.50Save your fingers! This new modeling tool makes rigging control systems easier, faster, less frustrating, and saves wear and tear on your fingers. Access into hard-to-reach areas are now much easier and you don't need a screw drivers that can slip and puncture the the adjacent surface.
For all #2-56 and #4-40 Metal Clevises
Replacement Fork Tips are available! Yes, if you accidently drop the pliers on a hard floor, the tips may break.
$32.95
EVF Shroud and Mounting Hardware We are making the EVF shroud and mounting hardware available for BVM kit builders. This setup will facilitate the placement of inlets and tailpipes in your electric jet model. Simply use the shroud while building, then pop in your EVF when your model is complete and ready for power. There is a $75.00 charge for the shroud, you may return it to BVM for a $50.00 refund. This is a service offered only by BVM.
$75.00NACA Inlets For summer operation. Adding these NACA flush cooling air inlets to an EVF powered jet will reduce the end-of-the-flight temperatures (motor/batteries) by 8-10°F compared to a non ventilated installation. The inlet design allows the cooling air to enter the fuselage with very little drag losses. The inlets can be added to a finished model.
$18.95The EVF "9er" units have a BVM purple anodized spinner. It looks real sporty and definitely identifies the product as "BVM". When the unit is installed in most jets, the spinner is not visible. Not so, with the all electric A-10.
$8.50Power Plugs EVF Battery Connectors Saves Soldering, Saves Weight, Improves Performance This BVM electric product is assembled in our Florida, USA facility using Dean's Ultra plugs. Power Plug 2 is for use with (2) Saddle CellsTM in series. Power Plug 3 is for use with (2) Saddle CellsTM and a Booster Pack. Your EVF will perform better with Power Plugs because of reduced resistance. We can measure the difference on our test stand. *Please Note, Power Plugs are manufactured per order. Please allow 2 weeks for processing.
$29.95BVM Series Power Plug 2 used with 10S 2 Male Input and 1 Male Output Less Restrictive, Runs Cooler and Handles More Current Tested over 130 AMP's BVM is constantly looking at new ways to improve products to better serve our customers. We have been testing these new Series Power Plugs for sometime now. The new Series Plugs handle higher currents better. They are larger in size and have larger contacting surfaces. Another benefit to the new plug is the ability to offer an Anti-Spark Plug to our ESC's on the 10S and 12S EVF units. Our new 14S EVF unit already has Anti-Spark in the ESC. These New Series Plugs are Male Inputs with Male Outputs. The BVM EVF system has a Female Plug already installed on it. This is done because we have an Anti-Spark Female Plug and a Non Anti-Spark Female Plug. 10S and 12S Versions will have the Anti-Spark Female Plug. The 14S Versions will have the Non Anti-Spark Female Plug since the ESC already has it built in. Anti-Spark Plugs are not rated above 50V use.
$33.99BVM Series Power Plug 3 used with 12S or 14S 3 Male Input and 1 Male Output Less Restrictive, Runs Cooler and Handles More Current Tested over 130 AMP's BVM is constantly looking at new ways to improve products to better serve our customers. We have been testing these new Series Power Plugs for sometime now. The new Series Plugs handle higher currents better. They are larger in size and have larger contacting surfaces. Another benefit to the new plug is the ability to offer an Anti-Spark Plug to our ESC's on the 10S and 12S EVF units. Our new 14S EVF unit already has Anti-Spark in the ESC. These New Series Plugs are Male Inputs with Male Outputs. The BVM EVF system has a Female Plug already installed on it. This is done because we have an Anti-Spark Female Plug and a Non Anti-Spark Female Plug. 10S and 12S Versions will have the Anti-Spark Female Plug. The 14S Versions will have the Non Anti-Spark Female Plug since the ESC already has it built in. Anti-Spark Plugs are not rated above 50V use.
$38.99Super Flow Inlet Duct for BVM F-86 63" ARF. In our efforts to constantly improve the efficiency of the BVM EVF powered airframes, we took a close look at the F-86 inlet duct. We found that with some contour changes and the inclusion of a center mounted spike we could gain some performance. The airflow from the nose cone inlet to the fan rotor is now much improved. This is all new tooling and both the static and flight tests confirm the performance increase. It's an easy to install, worthwhile upgrade to an EVF powered F-86. Installing this duct assembly in any existing BVM Sabre designed for EVF or D/F power will yield an additional 1 pound of static thrust. The weight addition is .6 oz.
INCLUDES:
Mylar Thrust Tube, FWD Battery Shelf, Inlet Assembly, Carbon Cord, and hardware
Power Plugs EVF Battery Connectors Saves Soldering, Saves Weight, Improves Performance This BVM electric product is assembled in our Florida, USA facility using Dean's Ultra plugs. Power Plug 2 is for use with (2) Saddle CellsTM in series. Power Plug 3 is for use with (2) Saddle CellsTM and a Booster Pack. Your EVF will perform better with Power Plugs because of reduced resistance. We can measure the difference on our test stand. *Please Note, Power Plugs are manufactured per order. Please allow 2 weeks for processing.
$34.95Classic Bandit Electric Tailpipe Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
Please specify the Length and Exit Diameter when you check out.
E Bandit Electric Tailpipe Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
Electra Tailpipe - 31.375" length 3.5" exit diameter Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
F-16 Electric Tailpipe - 26.875" length 3.45" exit diameter Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
F-16/ early Viper/ early Agg Tailpipe
F-4 Electric Tailpipe
F-80 Electric Tailpipe
F-86 (60") Tailpipe
Maverick PRO/Ultra Viper/Agg III Tailpipe
Maverick Tailpipe
Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
T-33 Tailpipe