BVM F-16 1:6 Nose Gear Door Light
Measurements:
32.2mm Length
17.3mm Width
15.35mm Depth
DISCLAIMER - This product is to be used with BVM Go Fly Jets only. Not guaranteed to work with other lighting systems. LED Light maximum voltage when testing is 3.7 volts.
$35.99BVM's Solid Replacement Rubber Tire
4-1/16" Tire for F-100, F86(80), and Ultra Bandit.
BVM offers Tire Change Tools to help assist in changing your BVM Tires. It's so easy you can even change a tire at the flying field. BVM has several different jet wheel sizes and provides the tools to match each one. There are the Tire Change Cone and Wooden Push Tool. The Wooden Push Tool is specifically designed to work with more than 1 size cone - refer to the product description for the correct Push Tool.
$35.004-3/4" Replacement Rubber Tire
NON-SOLID TIRE - Used with BVM Go Fly Gold Models: F-18 5.5, YAK 1:4.85
$35.00BVM Oxford LongSleeve - Small size with BVM Jets embordery
Teflon™ tough, this stylish shirt is made from a 65% polyester/35% cotton blend and is treated with Teflon™ fabric protector for stain resistance. It features a soft-touch finish, wrinkle resistance, a button-down collar, a double-back yoke, two side back pleats, a patch pocket with pencil compartment and bone-horn buttons.
**BRAND NEW - IN ORIGINAL PACKAGE. JUST CLEARING OUT OLD INVENTORY**
$35.00Hanes F260 Ultimate Cotton ® - Crewneck Sweatshirt
85% cotton, 15% poly
Low pill, high-stitch density PrintPro® XP fabric with 100% cotton face
Double-needle cover seamed neck, armholes and waistband
Cotton/polyester/spandex neck, cuffs and relaxed waistband for ultimate comfort
Size Chart
Small – 21 Body Width, 28 Full Body Length, 24 Sleeve Length
**BRAND NEW - IN ORIGINAL PACKAGE. JUST CLEARING OUT OLD INVENTORY**
$35.00About 3 hours of modeling time and some Aeropoxy are required to make the upgrade. As with any high performance model, it is wise to occasionally disassemble it and check the critical glue joints.
$35.00About 3 hours of modeling time and some Aeropoxy are required to make the upgrade. As with any high performance model, it is wise to occasionally disassemble it and check the critical glue joints.
$35.00CF Main Flex Plates- Super Bandit & Balsa Bandit-pr
$34.95Classic Bandit Electric Tailpipe Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
E Bandit Electric Tailpipe Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
Electra Tailpipe - 31.375" length 3.5" exit diameter Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
F-16/ early Viper/ early Agg Tailpipe
F-4 Electric Tailpipe
F-80 Electric Tailpipe
F-86 (60") Tailpipe
Maverick PRO/Ultra Viper/Agg III Tailpipe
Maverick Tailpipe
Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
Power Plugs EVF Battery Connectors Saves Soldering, Saves Weight, Improves Performance This BVM electric product is assembled in our Florida, USA facility using Dean's Ultra plugs. Power Plug 2 is for use with (2) Saddle CellsTM in series. Power Plug 3 is for use with (2) Saddle CellsTM and a Booster Pack. Your EVF will perform better with Power Plugs because of reduced resistance. We can measure the difference on our test stand. *Please Note, Power Plugs are manufactured per order. Please allow 2 weeks for processing.
$34.95T-33 Tailpipe
3-1/2" Replacement Rubber Tire
NON-SOLID TIRE - Used with BVM Go Fly Gold Models: F-16 1:5, YAK130 1:4.85, and Ultra Bandit evo
$34.50When flying off wet grass or a puddled runway, the nose wheel can spray water up into the wheel well. Since there are electrical components in that area of the fuselage, there is a chance that they could be affected. This plastic cover box can be installed to prevent a problem from occurring.
$34.50BVM Series Power Plug 2 used with 10S 2 Male Input and 1 Male Output Less Restrictive, Runs Cooler and Handles More Current Tested over 130 AMP's BVM is constantly looking at new ways to improve products to better serve our customers. We have been testing these new Series Power Plugs for sometime now. The new Series Plugs handle higher currents better. They are larger in size and have larger contacting surfaces. Another benefit to the new plug is the ability to offer an Anti-Spark Plug to our ESC's on the 10S and 12S EVF units. Our new 14S EVF unit already has Anti-Spark in the ESC. These New Series Plugs are Male Inputs with Male Outputs. The BVM EVF system has a Female Plug already installed on it. This is done because we have an Anti-Spark Female Plug and a Non Anti-Spark Female Plug. 10S and 12S Versions will have the Anti-Spark Female Plug. The 14S Versions will have the Non Anti-Spark Female Plug since the ESC already has it built in. Anti-Spark Plugs are not rated above 50V use.
$33.99BVM's Solid Replacement Rubber Tire
3-1/2" Tire F-4
BVM offers Tire Change Tools to help assist in changing your BVM Tires. It's so easy you can even change a tire at the flying field. BVM has several different jet wheel sizes and provides the tools to match each one. There are the Tire Change Cone and Wooden Push Tool. The Wooden Push Tool is specifically designed to work with more than 1 size cone - refer to the product description for the correct Push Tool.
$33.50Aluminum Nose Gear Flex Arms - F-16/ F-86 (pair) **LIMITED QUANTITY REMAINING**
$33.0035mm Door Cylinder USED IN: BVM F-16 1:6 scale PNP Nose Gear Door BVM YAK130 1:4 PNP Main Gear Door BVM F-18 1:5.5 PNP Main Gear Door
$32.99Save your fingers! This new modeling tool makes rigging control systems easier, faster, less frustrating, and saves wear and tear on your fingers. Access into hard-to-reach areas are now much easier and you don't need a screw drivers that can slip and puncture the the adjacent surface.
For all #2-56 and #4-40 Metal Clevises
Replacement Fork Tips are available! Yes, if you accidently drop the pliers on a hard floor, the tips may break.
$32.95
Bandit ARF MKI & MKII & eBandit Main Gear Reinforcement Kits.
$32.50F-18 1:5.5 Nose Gear Strut Attachment Pin & Brass Sleeve Assembly
$31.99This 3D printed Pitot Tube Mount can be used with a JetCat (or similar) Air Speed Sensors. Mount the airfoiled end to the fuselage such that the Pitot Tube is pointed to the front end of the model and close to parallel to the longitudinal axis. For accuracy, it is necessary that the Pitot Tube is at least 1/2" away from fuselage skin to not be affected by boundary layer flow. The plywood plate and screws allow attaching it to the fuselage skin. The fairing can be primed and painted to suit your needs.
$31.954-1/4" Replacement Rubber Tire
NON-SOLID TIRE - Used with BVM Go Fly Gold Models: F-16 1:6, Cougar, F-1, F-18F, YAK 1:4, L39 and Renegade
$30.00