Braided loom neatly organizes your servo wires and pneumatic tubing. Use in conjunction with the BVM O-Clips (BVM# PA-SR-0026)
$8.95We got
tired of fixing wing tip scratches and faced up to reality - it's just going to
happen occasionally. So, if your landings are not always perfect, you may also
find a need for some truly tough wingtip skids.
  Â
White LED Light with Heatsink DISCLAIMER - This product is to be used with BVM Go Fly Jets only. Not guaranteed to work with other lighting systems. LED light maximum voltage when testing is 3.7 volts.
$19.993/16" Wheel Bushing
Quantity - 1 per package (2 per wheel required)
Oil-Lite bushings are a bit darker in color (than brass), and more porous in texture if viewed with a magnifying glass.
$2.25Wheel Bushing Used On; F-16 1:5 Main Wheel, F-18 5.5 Main Wheel **BVM Wheels Need QTY 2 Bushings**
$6.50The one piece wheel hubs have Oil-Lite bushings pressed into each side. The gap between the bushings should be packed with Wheel Axle Grease. Practice has shown that most BVM wheels should be repacked about every 2 dozen flights.
$7.99Re-Formulated - Same Strength, Same Characteristics as original Vpoxy, Cures 25% Faster As good as Aeropoxy but cures in 1/2 the time. Vpoxy+ Kit includes: 2 Vpoxy+ Glue Cartridges, Dispensing Gun, 2:1 Plunger, 2 Long Glue Mix Nozzles, 4 Short Glue Mix Nozzles Not for use with EPO Foams. If your gluing EPO Foam, there is a special glue for that application. Check out Foam-Tac made by Beacon Adhesives.
$87.95Re-Formulated - Same Strength, Same Characteristics as original Vpoxy, Cures 25% Faster As good as Aeropoxy but cures in 1/2 the time. Not for use with EPO Foams. If your gluing EPO Foam, there is a special glue for that application. Check out Foam-Tac made by Beacon Adhesives.
$18.95Velcro / White adhesive back 2 X 6; (2) This Hook n' Loop product has a very aggressive adhesive backing and very aggressive Hook n' Loop gripping power. Cut to size with sharp scissors. Apply the prickly side to a smooth Zap or painted surface and the fuzzy side to a battery or receiver.
$7.50Velcro Strap / Black 3/8 X 24; (2) It conveniently hand separates (without scissors) in 6 inch lengths. You will find many other uses for it when gearing-up your model.
$5.10Velcro Strap / Black 3/4 X 24; (2) Can be used to reinforce the adhesive product (above) to add a firm retaining strap to hold batteries etc.
$9.25Velcro Strap / Black 1-1/2 X 32 Hook on one side, Loop on the other; this heavy duty strapping can be used to hold heavy batteries in the model. It can also serve to hold the models in a van or on a trailer shelf.
$8.50This infinitely adjustable, 1-1/2" wide 12 ft length, strap wraps onto itself for a secure hold. Hook on one side, loop on the other in one convenient piece.
$24.95Velcro / Black adhesive backed 3/4 X 36 Very convenient to mount EVF power batteries. Works similar to the white adhesive product #PA-SR-0083 but is sometimes more convenient to cut, peel, and stick.
$13.50The Ultra Bandit Jet-Foam Cradle is the largest in BVM's line of airframe handling products. The PVC tubes are longer (38") and the forward End Bracket is wider to carefully handle the inlet ducts without damage. For lots of handling, building, and transporting conveniences, the Ultra Bandit fuselage aft section is removable. This special Jet-Foam Cradle allows support of the front half (with the aft fuse section removed) to allow engine access, fuel tanks, etc. NOTE: Extra lengths (12 feet) of the 1-1/2 wide Velcro straps (BVM # PA-SR-0079) are available to assist in mounting the Jet Foam Cradle to a trailer shelf or floor for safe and soft transport. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$155.00Ultimate Air Trap Mount There are multiple ways to mount the Ultimate Air Trap in a turbine powered model. Whatever method you choose, it is important to be able to observe the fuel/air action in the U.A.T. during throttle-up test. Easy removal of the U.A.T. is important to check for security of the cap, fittings (twice a year), and any possible contamination. (Very rare if the fuel is filtered). This mounting kit provides all of these requirements and will allow the U.A.T. to be set at the most advantageous angle (slightly nose up). The mount can be glued or screwed to the fuselage structure.
$14.95We have flown it extensively in every BVM factory demo jet and have tried every possible maneuver and unusual attitude combined with every possible throttle position - you just can't make it quit! All BVM fuel cell packages (for BVM jets) now come standard with a U.A.T. The mystery material, duck bill shaped sack inside will deliver a solid stream of fuel (no bubbles) to the fuel pump even if the 4oz bottle should get 3/4th's full of air, which is very unlikely. This is a very high quality product for those turbine pilots who want to eliminate the possibility of an air bubble causing a flame out. The U.A.T. is placed in series between the last fuel tank and the fuel pump. The system is filled through the 3rd line in the U.A.T. The rectangular shaped tank can be mounted vertically or horizontally and produce the same results making it convenient to fit into just about any model and it will work with any model size turbine engine.
$74.95Three-Way Air Fitting will support 2MM or 3MM airline with included fittings.
$10.99