English
Categories
- PNP/Go Fly Accessories
- Kit Accessories
- HSD Jets
- PowerBox
- Carbon Fiber
- Air Systems
- Accessories
- Installation Organizers
- Building Materials
- Finishing Materials
- Adhesives
- Electric VioFan (EVF)
- Chargers / Power Supplies
- Electric Accessories
- Batteries
- Turbine Mounts & Straps
- Turbine Accessories
- Fuel Cells
- Fuel System Accessories
- Jersey Modeler
- Cockpits
- Lubricants
- PermaGrit
- Tools
- Radio Gear
- Pilots
- Landing Gear
- Wheels Tires and Brakes
- Jet Cases / Cradles
- Specials
- Apparel and Gifts
- Books
- Gift Certificates
- Penn Bags
Featured [more]
UAT Mount
UAT - Ultimate Air Trap
BobCat Composite Jet-Foam Cradle
The BobCat Composite Jet-Foam Cradle is designed to ease the handling of the model during the work shop assembly stage, field handling, and transport - Booms on or off. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$155.00
Bobcat Composite, Bobcat XL, and Classic Bandit Hopper Tank 16oz
Bobcat Composite, Bobcat XL, and Classic Bandit Hopper Tank 16 oz w/ hardware - No U.A.T. *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$125.00
BVM Cougar Jet-Foam Cradle
The Jet-Foam Cradle for the BVM Cougar is designed to allow you to work on the model right side up or upside down, exercise the landing gear and flaps, with or without the vertical fin attached. The Cradle can be used on the ground or on a portable 30" high table. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$165.00
Engine Strap Screw Clamp 85-90MM
Engine Strap Screw Clamp 85-90MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00
EVF 3 10s 9er
EVF ~3~ 10S power unit has been test flown in both the BVM Electra and Sabre Jet with excellent results. It delivers 16Lb of thrust (test cell) at 107 amps and runs very very cool. In-Flight motor temps registered a maximum of 136°F after the most demanding vertical climbs. The Castle Creation's Edge Lite HV160 is housed and kept cool in the EVF's epoxy fiberglass and Kevlar aft fairing for an all up weight of 2Lbs. 3oz. Utilizing ThunderPower 70C 6600 mAh LiPo's (10 cells) we are getting 6+ minute flights without stressing the batteries, i.e. using less than 80% of the capacity.
$1,595.00
General Purpose Jet-Foam Cradle
Originally developed for the BVM 84" Sabre Jet, this Jet-Foam Cradle works well for many medium size jets such as the Bandit, Electra, MiG-15, and F-100. The distance between the End Brackets can be adjusted on the PVC Tubes and the Velcro Straps will hold the model for field assembly, disassembly, and transport, as well as being very handy in the shop while you work on the model. Review the accompanying enclosures and the photos below to see the advantages a BVM Jet-Foam Cradle offers. Modify as desired A razor saw or sharp knife can be used to put a "V" notch in an End Bracket if that best suits your model. Outline the desired modification with tape, then cut. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$155.00
GFG 2MM Airline - Gray 12 Feet
Go Fly Gold Airline Gray 12 Feet
2MM OD, 1MM ID
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50
GFG 2MM Airline Black - 12 Feet
Go Fly Gold Airline Black - 12 Feet
GFG 2MM Airline Blue - 12 Feet
Go Fly Gold Airline Blue - 12 Feet
2MM OD, 1MM ID
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50
GFG 2MM Airline Clear - 12 Feet
Go Fly Gold Airline Clear 12 Feet
2MM OD, 1MM ID
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50
Hi-Flow Valve
| Made from 5/8" hex stock with a 5/16" spool and larger air passage holes. |
|
| Great for larger pneumatic retracts. | |
This offering from BVM facilitates more positive actuation of your retractable landing gear, especially when they are fitted with 3/4" to 1" diameter cylinders.
Attractively anodized in BVM's signature purple (Violet) color, the Hi-Flow Valve actuates easily with most mini servos and comes complete with a plywood mounting tab and screws.
O-Clips
| There are a number of devices on the R/C
market that help organize the installation of electronic and
pneumatic lines in your model. The "O-Clips" system will add a
new dimension to the task.  The "O-Clip" system is non-specific in regards to tubing diameter or wire size and allows grouping these components together where it is convenient,  Each package contains four each of three different sizes of "O-Clips", the appropriate size "O" rings (a few extra of each) and two rolled strips of 1/64" x 1/2" x 12" plywood. This group of 12 is sufficient for most medium to large size models. |
UAT - Ultimate Air Trap
We have flown it extensively in every BVM factory demo jet and have tried every possible maneuver and unusual attitude combined with every possible throttle position - you just can't make it quit! All BVM fuel cell packages (for BVM jets) now come standard with a U.A.T. The mystery material, duck bill shaped sack inside will deliver a solid stream of fuel (no bubbles) to the fuel pump even if the 4oz bottle should get 3/4th's full of air, which is very unlikely. This is a very high quality product for those turbine pilots who want to eliminate the possibility of an air bubble causing a flame out. The U.A.T. is placed in series between the last fuel tank and the fuel pump. The system is filled through the 3rd line in the U.A.T. The rectangular shaped tank can be mounted vertically or horizontally and produce the same results making it convenient to fit into just about any model and it will work with any model size turbine engine.
$74.95
Ultra Bandit Jet-Foam Cradle
The Ultra Bandit Jet-Foam Cradle is the largest in BVM's line of airframe handling products. The PVC tubes are longer (38") and the forward End Bracket is wider to carefully handle the inlet ducts without damage. For lots of handling, building, and transporting conveniences, the Ultra Bandit fuselage aft section is removable. This special Jet-Foam Cradle allows support of the front half (with the aft fuse section removed) to allow engine access, fuel tanks, etc. NOTE: Extra lengths (12 feet) of the 1-1/2 wide Velcro straps (BVM # PA-SR-0079) are available to assist in mounting the Jet Foam Cradle to a trailer shelf or floor for safe and soft transport. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$155.00
Air Fill Chuck
BVM Fill Chuck #2192 Fill Chuck swivel end to fit 1/4" hose on electronic pumps For use with BVM Fill Valve's.
$12.95
Bobcat Composite Canopy Deck Package
Bobcat Composite Canopy Deck Package (includes canopy) THIS PACKAGE INCLUDES THE CLEAR CANOPY.
$93.50
BVM Adaptor Plates JetCat P-100
BVM Engine Mounting Adaptor Plates for BobCat with JetCat P-100
$39.95
BVM Adaptor Plates JetCentral Cheetah
BVM Engine Mounting Adaptor Plates for KingCat with JetCentral Cheetah
$39.95
BVM Adaptor Plates JetCentral Rabbit
BVM Engine Mounting Adaptor Plates for BobCat with JetCentral Rabbit
$39.95
BVM Adaptor Plates KingTech K-100G
Engine Mounts Adaptors for: BVM BobCat Composite and KingTech K-100G
$39.95
Carbon Mat 8 1/2" X 22" 1/2 oz/sq. ft. 2 sheets
Carbon Mat 8 1/2" X 22" 1/2 oz/sq. ft. 2 sheets
$14.75
Engine Strap Screw Clamp 90-95MM
Engine Strap Screw Clamp 90-95MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00
#2 X 3/16" Button Head Panel Screws 30pk
#2 X 3/16 Button Head Panel Screws 30pk Jets, WWII models and even scale helicopters sometimes require removable panels that yield access to servos and other components. Jets also have other special requirements, such as attaching thin fiberglass parts. The socket head panel screws (SHPS) from BVM may be just what's needed to accomplish the task and have the finished product look great. The very small dome shaped head with its .050 hex socket and black finish will appear very scale-like in most applications. The 3/8 long self-tap screw thread is just right for attaching thin fiberglass panels made from BVM's Poly Ply materials. DISCLAIMER: Occasionally our supplier substitutes silver screws for black. If you prefer to have only black screws, please note this when placing online or phone orders.
$6.50
2:1 Plunger
2:1 Plunger for use with the glue dispenser gun. This will work with Aeropoxy, Vpoxy, and QT Poxy Glue Cartridges.
$7.95
3/8" Long Button Head Panel Screws 25pk
3/8 Long Button Head Panel Screws 25pk Jets, WWII models and even scale helicopters sometimes require removable panels that yield access to servos and other components. Jets also have other special requirements, such as attaching thin fiberglass parts. The socket head panel screws (SHPS) from BVM may be just what's needed to accomplish the task and have the finished product look great. The very small (5/32 dia) dome shaped head with its .050 hex socket and black finish will appear very scale-like in most applications. The 5/32 long or 3/8 long self-tap screw thread is just right for attaching thin fiberglass panels made from BVM's Poly Ply materials. DISCLAIMER: Occasionally our supplier substitutes silver screws for black. If you prefer to have only black screws, please note this when placing online or phone orders.
$7.50
Aluminum Cap Fittings
Aluminum Cap Fittings fits Sullivan and Dubro tanks.
Here is a fuel tank cap system that will not flex and deteriorate with time. The machined aluminum cap and threaded disc capture the standard rubber stopper and squeeze it securely with a 4-40 socket head machine screw. Results are a leak proof cap, even when pressure is applied to the fuel system.
The 5/32 diameter soft brass tubing allows freer flow of the fuel as required by some of today's larger engines. BVM uses this system on their ducted fan installations as well as for turbine fuel systems. Other specialty enthusiasts will surely want this fuel system improvement as well. Each cap system contains one rubber stopper for use with petroleum liquids, adaptable to Sullivan or Du-bro tanks.
$17.95
Bandit ARF MKII Fuel Cells
The Bandit fuel system consists of 2 conformal Kevlar fuel cells, an 8oz plastic header tank and the Ultimate Air Trap (U.A.T.) which provides 2.8 Liters of fuel. BVM's Aluminum Cap Fittings are supplied for use with the plastic hopper tank along with all fuel line necessary to plumb the system. The U.A.T. acts as an air bubble eliminator and final filter. NOTE: A large Kevlar header tank is available. *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$295.00
Bobcat Kevlar Fuel Cells
Bobcat Kevlar Fuel Cells (2.5 Liters) includes - 2 Kevlar tanks and hardware (assembly with Aeropoxy required), (1) Sullivan BT 16oz tank with BVM Aluminum Cap system, (1) U.A.T., T-Fittings, overflow fitting, and fuel tubing. *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$295.00
Bobcat XL Kevlar Fuel Cells
Bobcat XL Kevlar Fuel Cells (2.0 Liters) *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$375.00
Classic Bandit Kevlar Fuel Cells
Classic Bandit Kevlar Fuel Cells (2.4 Liters) *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$355.00