JR Transmitter Battery Upgrade Includes E-Z solder tabs for connecting + and - wires. BVM has been flying Sanyo eneloop cells for several months now with excellent results. Now, you can fly a whole weekend on one charge! These batteries have no memory effect and feature an extremely flat discharge curve providing consistent power longer than other cells. To install, simply remove 4 screws and a tape seal from the battery case, and resolder (2) tabs to the + and - terminals. As always, read the charging instructions that accompany the eneloop batteries.
$56.00When flying off wet grass or a puddled runway, the nose wheel can spray water up into the wheel well. Since there are electrical components in that area of the fuselage, there is a chance that they could be affected. This plastic cover box can be installed to prevent a problem from occurring.
$34.50KingCat Pylons (pair) complete with EZ-DROP's, air install and hardware
$159.99L-39 1:5 Clear Canopy Disclosures: BVM prides itself in providing a quality product delivered to customers on time. Due to the popularity of certain products, we can not guarantee that each item you have ordered will be in stock. If any items you ordered are not in stock, BVM will inform you immediately. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$65.00L-39 Main Flex Plates - PAIR Current Style
PLEASE SEE DIAGRAM FOR MEASUREMENTS.
$25.00L-39 Main Flex Plates - PAIR Original Style
PLEASE SEE DIAGRAM FOR MEASUREMENTS.
$25.00L-39 Main Strut Springs **This package is for one strut. If you need springs for both struts, order two packages**
$9.99BVM's Large Wooden Push Tool assists in changing the BVM Solid Rubber Tires, 4" and larger.
After removing the old tire from the rim. Insert the cone tool into the axle bushing of the rim. Place the tire over the cone. Place the Wooden Push Tool over the tire. Slowly push straigth down, keeping fingers clear from the underside. For larger wheels, it may be nesessary to place the wheel on the floor and stand on the push tool.
$8.50Main Gear Flex Mount Stiffener - Electra/Sabre
$19.00Bandit ARF MKI & MKII & eBandit Main Gear Reinforcement Kits.
$32.50BVM's Medium Wooden Push Tool assists in changing the BVM Solid Rubber Tires, 3" to 3-1/2" tires.
After removing the old tire from the rim. Insert the cone tool into the axle bushing of the rim. Place the tire over the cone. Place the Wooden Push Tool over the tire. Slowly push straigth down, keeping fingers clear from the underside. For larger wheels, it may be nesessary to place the wheel on the floor and stand on the push tool.
$8.50Assortment of Metric E'Clips and C'Clips Includes: EClip M2.5, EClip M3, EClip M4, EClip M5, CIRClip M8, and CIRClip M10
$8.50Multi Function 3-Way Block Valve. To be used in conjunction with the CCU. Each Valve controls an action. Example: Gear Up One Valve, Gear Down One Valve. Valve Blocks are available up to 9 functions and can be operated electronically or manually. They will also support Spring Assisted Cylinders. Primary use is for, but not limited to, Doors, Gear, Brakes, Speed Brakes, and Canopy. All Valve Blocks will come with 2MM and 3MM fittings for airline.
$179.00Multi Function 5-Way Block Valve. To be used in conjunction with the CCU. Each Valve controls an action. Example: Gear Up One Valve, Gear Down One Valve. Valve Blocks are available up to 9 functions and can be operated electronically or manually. They will also support Spring Assisted Cylinders. Primary use is for, but not limited to, Doors, Gear, Brakes, Speed Brakes, and Canopy. All Valve Blocks will come with 2MM and 3MM fittings for airline.
$299.00Multi Function 7-Way Block Valve. To be used in conjunction with the CCU. Each Valve controls an action. Example: Gear Up One Valve, Gear Down One Valve. Valve Blocks are available up to 9 functions and can be operated electronically or manually. They will also support Spring Assisted Cylinders. Primary use is for, but not limited to, Doors, Gear, Brakes, Speed Brakes, and Canopy. All Valve Blocks will come with 2MM and 3MM fittings for airline.
$419.00Multi Function 9-Way Block Valve. To be used in conjunction with the CCU. Each Valve controls an action. Example: Gear Up One Valve, Gear Down One Valve. Valve Blocks are available up to 9 functions and can be operated electronically or manually. They will also support Spring Assisted Cylinders. Primary use is for, but not limited to, Doors, Gear, Brakes, Speed Brakes, and Canopy. All Valve Blocks will come with 2MM and 3MM fittings for airline.
$539.00SPECIFICATIONS:
Wingspan 1500 mm (59.1 in)
Length 1900 mm (74.8 in)
Flying Weight 9.2kg (20.2 lb) with 1800cc Aviation kerosene
Configuration of turbine engine 8KG (required & not included)
Cruising speed -200 km/h
Flying time 4-6 mins (full throttle)
Wing area 47 dm2
Wing load 195.7 g/dm2
Main material 20 times EPO
Painting surface Matte environmental water-borne paint + decal
Suitable experience level ?Zero basis ?Beginner ?Intermediate ?Advanced
PNP Assembly difficulty ??10mins ???30mins ???60mins
Suitable for ambient temperature 0C-40C
Radio System 9 channel (required & not included)
Control System MFC-2085
Servos
7.4V 40gx1 Metal gear with 80mm lead (Elevator forward)
7.4V 25gx2 Metal gear with 560mm lead (Left & right ailerons forward)
7.4V 25gx2 Metal gear with 410mm lead (Left & right flaps x2 forward)
7.4V 25gx1 Metal gear with 80mm lead (Rudderx1 forward)
7.4V 17gx4 Metal gear with 180mm lead (Left & right Leading edge flapx4 forward)
7.4V 12gx2 Metal gear with 80mm lead with protection function (Left & right Speed brake x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Front wheel steering / cover plate x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Rear wheel cover plate x2 forward)
Recommended Battery 2S,7.4V,2200-5200mAhx2,LiPo with XT60 type plug (required & not included)
Ailerons Yes
Flaps Yes
Elevator Yes
Rudder (Vertical tail) Yes
The smoke system Included
Speed brake Yes
LED lights system Yes
Electromagnetic brake system Yes
Leading edge flap Yes
Reinforced gyro Selective configuration (not included)
Packaging / Size Packing Box + Outer Box (Card mark)/55.9x19.7x16.5(inch)
CG (Center of Gravity) 161 mm from the leading edge of the Main Wing
Landing Gears Metal electric retractable hydraulic landing gearx3(Nose gear double wheel)
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselagex1 pcs
Left main wingx1 pcs
Right main wingx1 pcs
Nosex1 pcs
Cockpitx1 pcs
Vertical tailx1 pcs
L&R Horizontal tailx1 pcs
Main wing carbon tube L=730mm external diameter 15.6mmx1 pcs
Accessories Bag 1 x1 pcs
Screw (HM3x10mm)x10 pcs (Wing/Horizontal tail/Vertical tail)
Screw (HM4x50mm)x4 pcs (Nose)
Accessories Bag 2 x1 pcs
100mm signal line(JR male + JR male) x8 pcs
Accessories Bag 3 x1 pcs
Filler tube x1 pcs
Left and right pitot tubes x2 pcs
Nose radar antenna x1 pcs
Upper and lower fuselage antenna x2 pcs
Remove the ribbon before flight x1 pcs
Oil tank overflow vent plug x1 pcs
Manualx1 pcs
REQUIRES:
8KG turbine engine (required & not included)
9 channel radio system (radio & receiver) (required & not included)
2S,7.4V,2200-5200mAhx2,LiPo with XT60 type plug (required & not included)
LiPo battery charger (required & not included)
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$1,499.90**Does Include Correct Tail Marking Decals**
SPECIFICATIONS:
Wingspan 1500 mm (59.1 in)
Length 1900 mm (74.8 in)
Weight ---
Turbine Engine 8KG (required & not included)
Cruising speed ---
Flying time ---
Wing area 47 dm2
Wing load ---
Main material 20 times EPO
Painting surface Matte environmental water-borne paint + decal
Suitable experience level ?Zero basis ?Beginner ?Intermediate ?Advanced
KIT Assembly difficulty ??10mins ???30mins ???60mins (For reference only)
Suitable for ambient temperature 0C-40C
Radio System 9 channel (required & not included)
Control System MFC-2085 (required & not included)
Servos (required & not included)
7.4V 40gx1 Metal gear with 80mm lead (Elevator forward)
7.4V 25gx2 Metal gear with 560mm lead (Left & right ailerons forward)
7.4V 25gx2 Metal gear with 410mm lead (Left & right flaps x2 forward)
7.4V 25gx1 Metal gear with 80mm lead (Rudderx1 forward)
7.4V 17gx4 Metal gear with 180mm lead (Left & right Leading edge flapx4 forward)
7.4V 12gx2 Metal gear with 80mm lead with protection function (Left & right Speed brake x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Front wheel steering / cover plate x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Rear wheel cover plate x2 forward)
Recommended Battery 2S,7.4V,2200-5200mAhx2,LiPo with XT60 type plug (required & not included)
Ailerons Yes
Flaps Yes
Elevator Yes
Rudder (Vertical tail) Yes
The smoke system Selective configuration (not included)
Speed brake Selective configuration (not included)
LED lights system Selective configuration (not included)
Electromagnetic brake system Selective configuration (not included)
Leading edge flap Selective configuration (not included)
Reinforced gyro Selective configuration (not included)
Packaging / Size Packing Box + Outer Box (Card mark)/55.9x19.7x16.5(inch)
CG (Center of Gravity) 161 mm from the leading edge of the Main Wing
Landing Gears Metal electric retractable hydraulic landing gearx3(Nose gear double wheel) (required & not included)
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselagex1 pcs
Left main wingx1 pc
Right main wingx1 pcs
Nosex1 pcs
Cockpitx1 pcs
Vertical tailx1 pcs
L&R Horizontal tailx1 pcs
Main wing carbon tube L=730mm external diameter 15.6mmx1 pcs
Accessories Bag 1 x1 pcs
Screw (HM3x10mm)x10 pcs (Wing/Horizontal tail/Vertical tail)
Screw (HM4x50mm)x4 pcs (Nose)
Accessories Bag 2 x1 pcs
100mm signal line(JR male + JR male) x8 pcs
Accessories Bag 3 x1 pcs
Filler tube x1 pcs
Left and right pitot tubes x2 pcs
Nose radar antenna x1 pcs
Upper and lower fuselage antenna x2 pcs
Remove the ribbon before flight x2 pcs
Oil tank overflow vent plug x1 pcs
Manualx1 pcs
REQUIRES:
8KG turbine engine (required & not included)
9 channel radio system (radio & receiver) (required & not included)
2S,7.4V,2200-5200mAhx2,LiPo with XT60 type plug (required & not included)
LiPo battery charger (required & not included)
Servos (required & not included)
7.4V 40gx1 Metal gear with 80mm lead (Elevator forward)
7.4V 25gx2 Metal gear with 560mm lead (Left & right ailerons forward)
7.4V 25gx2 Metal gear with 410mm lead (Left & right flaps x2 forward)
7.4V 25gx1 Metal gear with 80mm lead (Rudderx1 forward)
7.4V 17gx4 Metal gear with 180mm lead (Left & right Leading edge flapx4 forward)
7.4V 12gx2 Metal gear with 80mm lead with protection function (Left & right Speed brake x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Front wheel steering / cover plate x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Rear wheel cover plate x2 forward)
Metal electric retractable hydraulic landing gearx3 (required & not included)
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$689.90SPECIFICATIONS:
Wingspan 1500 mm (59.1 in)
Length 1900 mm (74.8 in)
Weight ---
Turbine Engine 8KG (required & not included)
Cruising speed ---
Flying time ---
Wing area 47 dm2
Wing load ---
Main material 20 times EPO
Painting surface Matte environmental water-borne paint + decal
Suitable experience level ?Zero basis ?Beginner ?Intermediate ?Advanced
KIT Assembly difficulty ??10mins ???30mins ???60mins (For reference only)
Suitable for ambient temperature 0C-40C
Radio System 9 channel (required & not included)
Control System MFC-2085 (required & not included)
Servos (required & not included)
7.4V 40gx1 Metal gear with 80mm lead (Elevator forward)
7.4V 25gx2 Metal gear with 560mm lead (Left & right ailerons forward)
7.4V 25gx2 Metal gear with 410mm lead (Left & right flaps x2 forward)
7.4V 25gx1 Metal gear with 80mm lead (Rudderx1 forward)
7.4V 17gx4 Metal gear with 180mm lead (Left & right Leading edge flapx4 forward)
7.4V 12gx2 Metal gear with 80mm lead with protection function (Left & right Speed brake x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Front wheel steering / cover plate x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Rear wheel cover plate x2 forward)
Recommended Battery 2S,7.4V,2200-5200mAhx2,LiPo with XT60 type plug (required & not included)
Ailerons Yes
Flaps Yes
Elevator Yes
Rudder (Vertical tail) Yes
The smoke system Selective configuration (not included)
Speed brake Selective configuration (not included)
LED lights system Selective configuration (not included)
Electromagnetic brake system Selective configuration (not included)
Leading edge flap Selective configuration (not included)
Reinforced gyro Selective configuration (not included)
Packaging / Size Packing Box + Outer Box (Card mark)/55.9x19.7x16.5(inch)
CG (Center of Gravity) 161 mm from the leading edge of the Main Wing
Landing Gears Metal electric retractable hydraulic landing gearx3(Nose gear double wheel) (required & not included)
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselagex1 pcs
Left main wingx1 pc
Right main wingx1 pcs
Nosex1 pcs
Cockpitx1 pcs
Vertical tailx1 pcs
L&R Horizontal tailx1 pcs
Main wing carbon tube L=730mm external diameter 15.6mmx1 pcs
Accessories Bag 1 x1 pcs
Screw (HM3x10mm)x10 pcs (Wing/Horizontal tail/Vertical tail)
Screw (HM4x50mm)x4 pcs (Nose)
Accessories Bag 2 x1 pcs
100mm signal line(JR male + JR male) x8 pcs
Accessories Bag 3 x1 pcs
Filler tube x1 pcs
Left and right pitot tubes x2 pcs
Nose radar antenna x1 pcs
Upper and lower fuselage antenna x2 pcs
Remove the ribbon before flight x2 pcs
Oil tank overflow vent plug x1 pcs
Manualx1 pcs
REQUIRES:
8KG turbine engine (required & not included)
9 channel radio system (radio & receiver) (required & not included)
2S,7.4V,2200-5200mAhx2,LiPo with XT60 type plug (required & not included)
LiPo battery charger (required & not included)
Servos (required & not included)
7.4V 40gx1 Metal gear with 80mm lead (Elevator forward)
7.4V 25gx2 Metal gear with 560mm lead (Left & right ailerons forward)
7.4V 25gx2 Metal gear with 410mm lead (Left & right flaps x2 forward)
7.4V 25gx1 Metal gear with 80mm lead (Rudderx1 forward)
7.4V 17gx4 Metal gear with 180mm lead (Left & right Leading edge flapx4 forward)
7.4V 12gx2 Metal gear with 80mm lead with protection function (Left & right Speed brake x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Front wheel steering / cover plate x2 forward)
7.4V 12gx2 Metal gear with 600mm lead with protection function (Rear wheel cover plate x2 forward)
Metal electric retractable hydraulic landing gearx3 (required & not included)
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$689.90Nose Gear Strut Pin Brass Adapter Will work with a 6MM Diameter Nose Gear Pin
$9.99The stock springs in all the BVM Go Fly Gold models are already a strong spring for each model.
BVM offers Upgrade Springs for customers that would like a stronger spring tension.
This is not required.
PACKAGE INCLUDES:
1 - 8MM X 20MM Spring
1 - 8MM X 20MM Spring
1 - Nylon Spacer
ENGRAVED Philips Wrench Set 4pcs Titanium Coated Tips
~FREE PERSONALIZED ENGRAVING ON THE TOOLS~
Take the guess work out of who's tool it is. 4 Piece Set Includes: PHILIPS 3.0mm X 180mm PHILIPS 4.0mm X 180mm PHILIPS 5.0mm X 180mm PHILIPS 6.0mm X 180mm
** Please note that the personalized custom engraved tools are made per order and the turn around time frame is about 4 - 6 weeks.
$24.99Philips Wrench Set 4pcs Titanium Coated Tips 4 Piece Set Includes: PHILIPS 3.0mm X 180mm PHILIPS 4.0mm X 180mm PHILIPS 5.0mm X 180mm PHILIPS 6.0mm X 180mm ** Please note this item is not personally engraved and will only have the BVM Logo and Tool Size.
$24.99The BVM Pump Mount can be used to secure most standard turbine fuel pumps or smoke pumps. The plastic mounts are adhesive backed. Additional screws may be used to secure the mount to the surface. Two 8" zip ties are included. Two mounts per package.
$5.95Red LED Light with heatsink DISCLAIMER - This product is to be used with BVM Go Fly Jets only. Not guaranteed to work with other lighting systems. LED Light maximum voltage when testing is 3.7 volts.
$19.99The stock springs in all the BVM Go Fly Gold models are already a strong spring for each model.
BVM offers Upgrade Springs for customers that would like a stronger spring tension.
This is not required.
PACKAGE INCLUDES:
4 - 12MM X 30MM Spring
1 - 10MM X 38MM Spring
1 - Nylon Spacer
Fighter Bombers of this era had underwing pylons to carry extra fuel to get them to the combat zone and engage in air-to-air or air-to-ground attacks. These highly detailed epoxy glass molded options allow you to fully adorn the Sabre Jet. This package requires assembly and paint.Â
$325.00Scuff Boards 10pk
Much of the sanding work required to build our models today involves the proper "scuffing" of the wood and plastic parts in preparation for gluing.
These #80 grit double sided, flexible boards are perfect for the job of giving the parts "tooth" for the glue to grab onto.
Critical tasks such as installation of laser cut formers into a fiberglass fuselage are a great application for the Scuff Boards. They are just flexible enough to attack the molded fiberglass and stiff enough to clean off burned edges of the laser cut ply parts. You can trim the ends with shears to adapt to each task.
Once you have some Scuff Boards on your workbench, you will find many other uses for these very handy and inexpensive tools. We certainly have in the BVM prototype shop.
Scuff Boards 20pk
Much of the sanding work required to build our models today involves the proper "scuffing" of the wood and plastic parts in preparation for gluing.
These #80 grit double sided, flexible boards are perfect for the job of giving the parts "tooth" for the glue to grab onto.
Critical tasks such as installation of laser cut formers into a fiberglass fuselage are a great application for the Scuff Boards. They are just flexible enough to attack the molded fiberglass and stiff enough to clean off burned edges of the laser cut ply parts. You can trim the ends with shears to adapt to each task.
Once you have some Scuff Boards on your workbench, you will find many other uses for these very handy and inexpensive tools. We certainly have in the BVM prototype shop.
These stainless steel socket head, self tapping cap screws (with built-in washer) are extremely handy for mounting servos and small parts in any model aircraft. #2 X 7/16" SSSH, 75 PACK
$7.95