Fuel Line Spring Clips - 6MM 10 per package For: Standard Fuel Systems The 6mm clips can be used on most fittings except those inside the fuel tanks. Safety wire (BVM #2800) is used to secure the flexible tubing to those fittings. The standard size clips will secure the 6mm fuel tubing to 5/32” brass tubes as shown. Be cautious with the pliers to not pinch the clips more than necessary. Pull test the fuel lines to check for security after the clips are in place.
$6.95Fuel Line Spring Clips - 8MM 10 per package For: Hi-Flow Fuel Systems The 8mm clips can be used on most fittings except those inside the fuel tanks. Safety wire (BVM #2800) is used to secure the flexible tubing to those fittings. Be cautious with the pliers to not pinch the clips more than necessary. Pull test the fuel lines to check for security after the clips are in place.
$7.95Remove Before Flight. Handling your Kerosene powered model is a lot less messy if you plug off the fuel system overflow vent. You prevent the stinky spills in your vehicle and workshop. But, if you take-off with the vent still plugged, your engine will starve for fuel and flame out, usually one or two minutes into the flight. Unfortunately, this has happened to two customers recently. BVM's "Remove Before Flight" Vent Plug solves the problem. It would be hard to taxi out and not see the Red Flag dragging on the ground.
$11.99Originally developed for the BVM 84" Sabre Jet, this Jet-Foam Cradle works well for many medium size jets such as the Bandit, Electra, MiG-15, and F-100. The distance between the End Brackets can be adjusted on the PVC Tubes and the Velcro Straps will hold the model for field assembly, disassembly, and transport, as well as being very handy in the shop while you work on the model. Review the accompanying enclosures and the photos below to see the advantages a BVM Jet-Foam Cradle offers. Modify as desired A razor saw or sharp knife can be used to put a "V" notch in an End Bracket if that best suits your model. Outline the desired modification with tape, then cut. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$155.00Go Fly Gold Airline Gray 12 Feet
2MM OD, 1MM ID
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50Go Fly Gold Airline Black - 12 Feet
Go Fly Gold Airline Blue - 12 Feet
2MM OD, 1MM ID
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50Go Fly Gold Airline Clear 12 Feet
2MM OD, 1MM ID
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50Green LED Light with heatsink DISCLAIMER - This product is to be used with BVM Go Fly Jets only. Not guaranteed to work with other lighting systems. LED Light maximum voltage when testing is .7 volts.
$19.99BVM Hatch Latch is a quick release mechanism for hatches and cowls. Scuff and glue to the inside of the fiberglass skin.
$9.50Heat Shield + brush-on ceramic coating High Temperature exhaust gases from both turbine and piston engines are sometimes unavoidably close to parts of the airframe. Tailpipes and mufflers contain the flame but the convective heat can be too much for the surrounding balsa, plastic, or fiberglass structures. Three brushed on coats of this water based, ceramic material, "Heat Shield" will protect those exposed parts of your model. Simply treat the inside of the engine cowl (piston engines) or the inside of the aft fuselage (turbine) and the surface temperature of the model will remain cool. In the unusual case of a turbine tailpipe fire on start up, you will have several seconds longer to extinguish it before any damage to the model occurs. Heat Shield comes in an 8 oz. can and is easily applied with a brush, clean up with soapy water. For extra protection the thickness can be built up with additional layers of fiberglass cloth and Heat Shield. Experimenters can purchase this product and do their own testing if the above information is insufficient.
$18.25Heavy Clunks for Turbine Fuel Tanks These heavy fuel pick up "Clunks" will improve the function of your jet fuel tanks. They are 2 1/2 times the weight of the standard parts, yet still fit through the neck of the BVM Kevlar Fuel Tank hardware.
$4.75BVM Heavy Duty 1/8" OD, .066" ID Black 12FT
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50BVM Heavy Duty 1/8" OD, .066" ID Blue 12FT
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50BVM Heavy Duty 1/8" OD, .066" ID Grey 12FT
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50BVM Heavy Duty 1/8" OD, .066" ID Red 12FT
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50BVM Heavy Duty 1/8" OD, .066" ID White 12FT
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50BVM Heavy Duty 1/8" OD, .066" ID Yellow 12FT
NOTE: Thickness can/will vary. During the manufacturing process the tubing is extruded. It is common practice to stretch the tubing before use to easily work with collars and fittings.
$9.50Hi Flow Aluminum Cap Fittings Here is a fuel tank cap system that will not flex and deteriorate with time. The machined aluminum cap and threaded disc capture the standard rubber stopper and squeeze it securely with a 4-40 socket head machine screw. Results are a leak proof cap, even when pressure is applied to the fuel system. The 3/16 diameter soft brass tubing allows freer flow of the fuel as required by some of today's larger engines. BVM uses this system on their ducted fan installations as well as for turbine fuel systems. Other specialty enthusiasts will surely want this fuel system improvement as well. Each cap system contains one rubber stopper for use with glow fuel and one compatible with petroleum liquids, adaptable to Sullivan or Du-bro tanks.
$25.95G-10 (Epoxy F/G Plate Stock) - 3 per pack BVM developed the Hi-Flow Fuel System to benefit performance and reliability of model jet engines in the 180N (40# of thrust) class and larger. As stated on the BVM Hi-Flow web-page link, everything that the fuel passes through from the clunk to the engine fuel pump has been enlarged for higher volume, lower resistance, fuel flow.
$11.95Hi-Flow UAT with line reducer, 8mm tubing, 6mm tubing, fill plug
We have flown it extensively in every BVM factory demo jet and have tried every possible maneuver and unusual attitude combined with every possible throttle position - you just can't make it quit! All BVM fuel cell packages (for BVM jets) now come standard with a U.A.T. The mystery material, duck bill shaped sack inside will deliver a solid stream of fuel (no bubbles) to the fuel pump even if the 4oz bottle should get 3/4th's full of air, which is very unlikely. This is a very high quality product for those turbine pilots who want to eliminate the possibility of an air bubble causing a flame out. The U.A.T. is placed in series between the last fuel tank and the fuel pump. The system is filled through the 3rd line in the U.A.T. The rectangular shaped tank can be mounted vertically or horizontally and produce the same results making it convenient to fit into just about any model and it will work with any model size turbine engine.
$84.95Made from 5/8" hex stock with a 5/16" spool and larger air passage holes. |
|
Great for larger pneumatic retracts. |
This offering from BVM facilitates more positive actuation of your retractable landing gear, especially when they are fitted with 3/4" to 1" diameter cylinders.
Attractively anodized in BVM's signature purple (Violet) color, the Hi-Flow Valve actuates easily with most mini servos and comes complete with a plywood mounting tab and screws.
SPECIFICATIONS:
Wingspan: 1344mm (52.9in)
Length: 1809mm (71.2in)
Flying Weight: 8.5kg (18.7 lb) (with 1800cc Aviation kerosene)
Turbine Engine: 6-8KG brushless (required & not included)
Cruising speed: 150-200 km/h
Flying time: 3-5 mins
Wing area: 47.6 dm2
Wing load: 178.6 g/dm2
Main material: 20 times the import of aeromodelling EPO
Painting surface: Matte environmental water-borne paint + decal
Suitable experience level: ?Zero basis ?Beginner ?Intermediate ?Advanced
PNP Assembly difficulty: ??10mins ???30mins ???60mins
Suitable for ambient temperature: 0C-40
Radio System: 6 channel (required & not included)
Control System: MFC-2085
Servos (All 7.4V High voltage)
40gx2 Metal gear with 60mm lead (left & right Horizontal tail forward)
25gx2 Metal gear with 150mm lead (left & right Aileron forward)
25gx1 Metal gear with 230mm lead (Rudder forward)
12gx2 Metal gear with 480mm lead (with protection function) (Left & right rear cover plate forward)
12gx1 Metal gear with 480mm lead (with protection function) (Front cover plate forward)
12gx1 Metal gear with 320mm lead (with protection function) (Front wheel steering forward)
12gx1 Metal gear with 480mm lead (Front wheel 360 locking forward)
12gx1 Metal gear with 480mm lead (Rear wheel 360 locking reverse)
12gx1 Metal gear with 480mm lead (Rear wheel 360 locking forward)
Recommended Battery 2S,7.4V,3300-5200mAhx2,LiPo with XT60 type plug (required & not included)
Ailerons: Yes
Flaps: No
Elevator (Horizontal tail) Yes
Rudder (Vertical tail) Yes
The smoke system No
LED lights system Yes
Electromagnetic brake system Yes
Reinforced gyro Selective configuration (not included)
Packaging / Size Packing Box + Outer Box (Card mark) /1456x518x337(mm)
CG (Center of Gravity) 155-160mm from the leading edge of the Main Wing
Landing Gears All-metal simulation electronic retractable landing gearx3
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselagex1
Left Wingx1
Right Wingx1
Nosex1
Cockpit canopyx1
Vertical Stabilizerx1
Left Horizontal tailx1
Right Horizontal tailx1
L/R Auxiliary tankx1
L/R wingtip missilex1
L/R wingtip missile pylonx1
L/R No.1 missilex1
L/R No.2 missilex1
L/R tail finsx1
Main wing carbon tube L=400mm external diameter 10mmx2
Accessories Bag x1
Fuselage antenna x1
Pitotx1
Screw (HA3x14mm)x10 (Nose & Engine)
Screw (HM3x6mm)x2 (Horizontal tail)
Screw (HA3x10mm)x8 (Tail nozzle & Vertical)
Screw (KA3x16mm)x8 (Missile)
Screw (KA3x20mm)x8 (Missile)
Screw (KM3x60mm)x8 (Auxiliary tank)
Screw (HM3x10mm)x8 (Main wing)
HF-16 V2 Manualx1
MFC-2085 Manualx1
REQUIRES:
SW 6-8KG brushless (required & not included)
6 channel radio system (radio & receiver) (required & not included)
2S,7.4V,3300-5200mAhx2,LiPo with XT60 plug (required & not included)
LiPo battery charger (required & not included)
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$1,529.90SPECIFICATIONS:
Wingspan 1300 mm (51.2 in)
Length 2115 mm (83.3 in)
Weight ---
Turbine Engine 8KG-12KG (required & not included)
Cruising speed ---
Flying time ---
Wing area 64 dm2
Wing load ---
Main material 20 times EPO
Painting surface Matte environmental water-borne paint + decal
Suitable experience level Advanced
KIT Assembly difficulty ??10mins ???30mins ???60mins (For reference only)
Suitable for ambient temperature 0C-40C
Radio System 10 channel (required & not included)
Control System MFC-2085 (required & not included)
Servos (required & not included)
7.4V 40gx1 Metal gear with 450mm lead (Canard wing forward)
7.4V 25gx2 Metal gear with 80mm lead (Left & right ailerons forward)
7.4V 25gx2 Metal gear with 80mm lead (Elevatorx2 forward)
7.4V 25gx1 Metal gear with 80mm lead (Rudderx1 forward)
7.4V 25gx2 Metal gear with 80mm lead (Vectoring nozzlex2 forward)
7.4V 12gx1 Metal gear with 500mm lead with protection function (Front wheel cover plate forward)
7.4V 12gx3 Metal gear with 500mm lead with protection function (Front wheel steering / Rear wheel cover plate forward)
Recommended Battery 2S,7.4V,3200mAhx2,LiPo with XT60 type plug (required & not included)
Ailerons Yes
Canard wing Yes
Elevator Yes
Rudder (Vertical tail) Yes
The smoke system Selective configuration (not included)
LED lights system Selective configuration (not included)
Electromagnetic brake system Selective configuration (not included)
Vectoring nozzle Selective configuration (not included)
Reinforced gyro Selective configuration (not included)
Packaging / Size Packing Box + Outer Box (Card mark)/60 21.3 14.8(inch)
CG (Center of Gravity) 238-242 mm from the leading edge of the Main Wing
Landing Gears Metal electric retractable hydraulic landing gearx3 (required & not included)
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselagex1 pcs
Left main wingx1 pcs
Right main wingx1 pcs
Nosex1 pcs
Cockpitx1 pcs
Vertical tailx1 pcs
L&R Canard wingx1 pcs
Air inletx1 pcs
Caudal finx1 pcs
1# Main wing carbon tube L=520mm external diameter 16mmx1 pcs
2# Main wing carbon tube L=540mm external diameter 10mmx1 pcs
Accessories Bag 1 x1 pcs
Screw (HA3x10mm)x6 pcs (Horizontal tail)
Screw (HM3x65mm)x2 pcs (Wing)
Screw (HM4x45mm)x4 pcs (Wing)
Screw (HM3x6mm)x4 pcs (Vertical tail / Nose)
Accessories Bag 2 x1 pcs
100mm signal line (JR male+JR male) x8 pcs
Accessories Bag 3 x1 pcs
Filler tube x1 pcs
Left and right pitot tubes x2 pcs
Nose radar antenna x1 pcs
Upper and lower fuselage antenna x2 pcs
Remove the ribbon before flight x1 pcs
Oil tank overflow vent plug x1 pcs
Manualx1 pcs
REQUIRES:
8KG-12KG turbine engine (required & not included)
10 channel radio system (radio & receiver) (required & not included)
2S,7.4V,3200mAhx2,LiPo with XT60 type plug (required & not included)
LiPo battery charger (required & not included)
Servos
7.4V 40gx1 Metal gear with 450mm lead (Canard wing forward)
7.4V 25gx2 Metal gear with 80mm lead (Left & right ailerons forward)
7.4V 25gx2 Metal gear with 80mm lead (Elevatorx2 forward)
7.4V 25gx1 Metal gear with 80mm lead (Rudderx1 forward)
7.4V 25gx2 Metal gear with 80mm lead (Vectoring nozzlex2 forward)
7.4V 12gx1 Metal gear with 500mm lead with protection function (Front wheel cover plate forward)
7.4V 12gx3 Metal gear with 500mm lead with protection function (Front wheel steering / Rear wheel cover plate forward)
Metal electric retractable hydraulic landing gearx3 (required & not included)
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$899.90SPECIFICATIONS:
Wingspan 1300 mm (51.2 in)
Length 2115 mm (83.3 in)
Flying Weight 10.5kg (23.1 lb) with 1800cc Aviation kerosene
Configuration of turbine engine 8KG-12KG (required & not included)
Cruising speed 160-180 km/h
Flying time 4-6 mins (full throttle)
Wing area 64 dm2
Wing load 164.1 g/dm2
Main material 20 times EPO
Painting surface Matte environmental water-borne paint + decal
Suitable experience level Advanced
PNP Assembly difficulty ??10mins ???30mins ???60mins
Suitable for ambient temperature 0C-40C
Radio System 10 channel (required & not included)
Control System MFC-2085
Servos
7.4V 40gx1 Metal gear with 450mm lead (Canard wing forward)
7.4V 25gx2 Metal gear with 80mm lead (Left & right ailerons forward)
7.4V 25gx2 Metal gear with 80mm lead (Elevatorx2 forward)
7.4V 25gx1 Metal gear with 80mm lead (Rudderx1 forward)
7.4V 25gx2 Metal gear with 80mm lead (Vectoring nozzlex2 forward)
7.4V 12gx1 Metal gear with 500mm lead with protection function (Front wheel cover plate forward)
7.4V 12gx3 Metal gear with 500mm lead with protection function (Front wheel steering / Rear wheel cover plate forward)
Recommended Battery 2S,7.4V,3200mAhx2,LiPo with XT60 type plug (required & not included)
Ailerons Yes
Canard wing Yes
Elevator Yes
Rudder (Vertical tail) Yes
The smoke system Yes
LED lights system Yes
Electromagnetic brake system Yes
Vectoring nozzle Yes
Reinforced gyro Selective configuration (not included)
Packaging / Size Packing Box + Outer Box (Card mark)/60x21.3x14.8(inch)
CG (Center of Gravity) 238-242 mm from the leading edge of the Main Wing
Landing Gears Metal electric retractable hydraulic landing gearx3
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselagex1 pcs
Left main wingx1 pcs
Right main wingx1 pcs
Nosex1 pcs
Cockpitx1 pcs
Vertical tailx1 pcs
L&R Canard wingx1 pcs
Air inletx1 pcs
Caudal finx1 pcs
1# Main wing carbon tube L=520mm external diameter 16mmx1 pcs
2# Main wing carbon tube L=540mm external diameter 10mmx1 pcs
Accessories Bag 1 x1 pcs
Screw (HA3x10mm)x6 pcs (Horizontal tail)
Screw (HM3x65mm)x2 pcs (Wing)
Screw (HM4x45mm)x4 pcs (Wing)
Screw (HM3x6mm)x4 pcs (Vertical tail / Nose)
Accessories Bag 2 x1 pcs
100mm signal line (JR male+JR male) x8 pcs
Accessories Bag 3 x1 pcs
Filler tube x1 pcs
Left and right pitot tubes x2 pcs
Nose radar antenna x1 pcs
Upper and lower fuselage antenna x2 pcs
Remove the ribbon before flight x1 pcs
Oil tank overflow vent plug x1 pcs
Manualx1 pcs
REQUIRES:
8KG-12KG turbine engine (required & not included)
10 channel radio system (radio & receiver) (required & not included)
2S,7.4V,3200mAhx2,LiPo with XT60 type plug (required & not included)
LiPo battery charger (required & not included)
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$1,699.90SPECIFICATIONS:
Wingspan:1245mm (49in)
Length:1809mm (71.2in)
Weight: 3.1kg (6.82 lb) (for reference only )
S-EDF/Motor: S-EDF 105mm 4270/750KV brushless (required & not included)
Number of EDF Blade: 11 blades (required & not included)
Cruising speed: about 180 km/h (For reference only )
Flying time: about 3-5 mins (For reference only )
Wing area: 47 dm2
Wing load: 129.8 g/dm2 (For reference only )
Main material: 35 times EPO
Painting surface: matte paint
Suitable experience level ?Zero basis ?Beginner ?Intermediate ?Advanced
PNP Assembly difficulty ??10mins ???30mins ???60mins
Suitable for ambient temperature: 0C-40C
Radio System: 6 channel (required & not included)
ESC: 160A/12S Hobbywing AS150 (required & not included)
Control System: MFC-2085 (required & not included)
Servos: (required & not included)
25gx4 Metal gear with 150mm lead (Elevator & ailerons)
12gx1 Metal gear with 260mm lead (Rudder)
12gx1 Metal gear with 600mm lead (Nose wheel steering)
12gx1 Metal gear with 460mm lead Rev (Nose door servo)
12gx1 Metal gear with 400mm lead Rev (left door servo)
12gx1 Metal gear with 400mm lead (Right door servo)
12gx3 Metal gear (360 lock Hatch cover)
Recommended MFC-2085 Battery: 2S,7.4V,1800-2000mAh,LiPo with XT60 or T type plug (required & not included)
Recommended Power Battery: 6S,22.2V,5000-6000mAhx2,LiPo with AS150 type plug (required & not included)
Ailerons: Yes
Flaps: No
Elevator (Horizontal tail): Yes
Rudder (Vertical tail): Yes
General landing gear control system: No
LED lights system: No
Electromagnetic brake system: No
Reinforced gyro selective configuration (not included)
Packaging / Size Packing Box + Outer Box (Card mark)/145.6x51.8x33.7(cm)
CG (Center of Gravity): 178mm from the leading edge of the Main Wing
Landing Gears: Metal electric retractable hydraulic landing gearx3 (required & not included)
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselagex1
Left Wingx1
Right Wingx1
Left Horizontal Stabilizerx1
Right Horizontal Stabilizerx1
Vertical Stabilizerx1
Nosex1
Cockpit canopyx1
Left missilex1
Right missilex1
Left tail finx1
Right tail finx1
Main wing carbon tube L=320mm diameter=10mmx2
White Stickerx1
Accessories Bag 1 x1
Horizontal steel wire rod(3x88mm)x2 (Horizontal Stabilizer)
Aileron steel wire rod(1.8x88mm)x2 (Aileron)
Wing lampshadex2
Fuselage lampshadex6
Vertical Stabilizer lampshadex2
Nylon cable tiesx5
Screw (PWA2x8mm)x8 (Control box)
Steering steel wire(1.5x35mm)x1 (Nose landing gear)
Wire rod steel wire(1.8x60mm)x1 (Vertical Stabilizer)
Wire rod steel wire(1.7x65mm)x1 (Nose wheel locking servo)
Wire rod steel wire(1.7x65mm)x1 (Left wheel locking servo)
Wire rod steel wire(1.2x41mm)x2 (Main wheel Cover)
Wire rod steel wire(1.2x41mm)x1 (Nose wheel Cover)
Screw (PM2.5x6mm)x1 (Main wheel Cover)
Screw (PM2.5x10mm)x1 (Main wheel Cover)
Wire rod steel wire(1.7x80mm)x1 (Right wheel locking servo)
Screw (PM3x12mm)x4 (Horizontal Stabilizer rod fixation with self-locking nut)
Screw (PM2x10mm)x6 (Wing/vertical Stabilizer rod fixation with self-locking nut)
Accessories Bag 2 x1
Screw (HM3x6mm)x2 (Horizontal Stabilizer)
Screw (HA3x10mm)x4 (Tail nozzle)
Screw (HM3x10mm)x4 (Wing)
Screw (HA3x8mm)x4 (Vertical Stabilizer)
Screw (HA3x14mm)x5 (Nose 1,Engine 4)
Accessories Bag 3 x1
Screw (HM3x10mm)x4 (Wing Spare)
Screw (HA3x14mm)x5 (Nose 1,Engine 4 Spare)
Screw (HA3x8mm)x4 (Vertical Stabilizer Spare)
Screw (HA3x10mm)x4 (Tail nozzle Spare)
Accessories Bag 4 x1
Nylon rocker arm of the servo x2 (Spare)
Nylon antennax1
Nylon airspeed tubex1
Manualx1
REQUIRES:
6+ channel radio system (radio & receiver)
2S,7.4V,1800-2000mAh,LiPo with XT60 or T type plug (MFC-2085)
6S,22.2V,5000-6000mAhx2,LiPo with AS150 type plug (S-EDF)
LiPo battery charger
Landing gear
Servos
S-EDF 105mm 4270/750KV brushless motor
MFC-2085 Control System
All wire
ESC 160A/12S Hobbywing AS150
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$1,249.90SPECIFICATIONS:
Wingspan 1720 mm (67.7 in)
Length 1715 mm (67.5 in)
Flying Weight 8 kg (15.4 lb) with 12S / 22.2V / 5200mAh / 45C Li-Pox2 PCS
Flying time 3-5 minutes
Wing area 64.34 dm2
Wing load 124.3 g/dm2
Main material 35 times EPO
Painting surface Matte environmental water-borne paint + decal
Suitable for ambient temperature 0C-40C
Radio System 8 channel (required & not included)
Control System MFC-2085
Motor 5268-KV640(Inner rotor)
EDF S-EDF 120mm-10 blade
ESC Hobbywing 160A brushless
Servos
25gx2 Metal gear with 560mm lead (Left & Right ailerons forward)
25gx2 Metal gear with 410mm lead (Left & Right flap forward)
25gx3 Metal gear with 190mm lead (Left & Right Elevator / Vertical tail forward)
25gx1 Metal gear with 230mm lead (Front wheel cover plate forward)
7.4V 12gx3 Metal gear with 380mm lead with protection function (Nose wheel steering / Rear wheel cover plate forward)
7.4V 12gx2 Metal gear with 80mm lead with protection function (Retarder plate forward)
Recommended Power Battery 6S,22.2V,5200mAh,45Cx2,LiPo with AS150 type plug (required & not included)
Recommended Receiver Battery 2S,7.4V,2200-5200mAhx2,LiPo with XT60 type plug (required & not included)
Ailerons Yes
Flaps Yes
Elevator (Horizontal tail) Yes
Rudder (Vertical tail) Yes
LED lights system Yes
Electromagnetic brake system Yes
Retarder plate Yes
Reinforced gyro Selective configuration (not included)
Packaging / Size Pearl cotton 3D Inner box + Outer Box /1320x550x440(mm)
CG (Center of Gravity) 300-305mm from the leading edge of the Main Wing
Landing Gears All metal hydraulic simulation electric retractable landing gearx3
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselagex1 pcs
Left main wingx1 pcs
Right main wingx1 pcs
Nosex1 pcs
Cockpitx1 pcs
Vertical tailx1 pcs
Left Auxiliary oil tankx1 pcs
Right Auxiliary oil tankx1 pcs
Horizontal tail x1 pcs
Main wing bolt rod 1 L=720mm external diameter 20mmx1 pcs
Accessories Bag 1 x1 pcs
Screw (HA4x45mm)x4 pcs (Horizontal tail)
Screw (HM4x20mm)x4 pcs (Main wing)
Screw (HM4x16mm)x4 pcs (Main wing)
Screw (HA3x10mm)x16 pcs (Vertical tail)
Screw (HM4x60mm)x4 pcs (Nose + Fuselage)
Screw (HM4x70mm)x8 pcs (Auxiliary oil tank)
Accessories Bag 2 x1 pcs
100mm signal line (JR male+JR male) x8 pcs
Head fixed plastic partsx4 pcs
3mm L-type hexagon wrenchx1 pcs
4mm L-type hexagon wrenchx1 pcs
Wing antenna x1 pcs
HME-262 Manualx1 pcs
MFC-2085 Manualx1 pcs
REQUIRES:
8 channel radio system (radio & receiver) (required & not included)
6S,22.2V,5200mAh,45Cx2,LiPo with AS150 type plug (required & not included)
2S,7.4V,2200-5200mAhx2,LiPo with XT60 type plug (required & not included)
LiPo battery charger (required & not included)
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$1,399.90
SPECIFICATIONS:
Wingspan: 2018 mm (79.4 in)
Length: 1800 mm (70.9 in)
Flying Weight: 10.7kg (23.5 lb) with 1800cc Aviation kerosene
Turbine Engine: SW80B 8KG brushless / SW60B 6KG brushless (required & not included)
Cruising speed: 150?200 km/h
Flying time: 3?5 mins (full throttle)
Wing area: 56.5 dm2
Wing load: 184.1 g/dm2
Main material: 20 times EPO
Painting surface: matte paint
Suitable experience level: ?Zero basis ?Beginner ?Intermediate ?Advanced
PNP Assembly difficulty: ??10mins ???30mins ???60mins
Suitable for ambient temperature: 0??40?
Radio System: 7 channel (required & not included)
Control System: MFC-2085
Servos
7.4V 25g×2 Metal gear with 480mm lead (left & right ailerons forward)
7.4V 25g×2 Metal gear with 230mm lead (Flap×2 forward)
7.4V 25g×3 Metal gear with 80mm lead (elevator×2 & rudder×1 forward)
7.4V 12g×1 Metal gear with 380mm lead with protection function (Nose wheel steering forward)
7.4V 12g×1 Metal gear with 320mm lead with protection function (Front wheel cover plate forward)
7.4V 12g×2 Metal gear with 80mm lead with protection function (Rear wheel cover plate forward)
Recommended Battery 2S,7.4V,5200mAh×2,LiPo with XT60 type plug (required & not included)
Ailerons Yes
Flaps Yes
Elevator (Horizontal tail) Yes
Rudder (Vertical tail) Yes
The smoke system No
LED lights system Yes
Electromagnetic brake system Yes
Reinforced gyro Selective configuration (not included)
Packaging / Size Packing Box + Outer Box(Card mark)/52.56×21.3×16.9(inch)
CG (Center of Gravity) 180mm from the leading edge of the Main Wing
Landing Gears Metal electric retractable hydraulic landing gear×3
Battery Charger LiPo battery charger (required & not included)
PACKAGE INCLUDES:
Fuselage×1 pcs
Left main wing×1 pcs
Right main wing×1 pcs
Left Horizontal tail ×1 pcs
Right Horizontal tail×1 pcs
Vertical tail×1 pcs
Nose×1 pcs
Cockpit×1 pcs
Left auxiliary tank×1 pcs
Right auxiliary tank×1 pcs
1# Main wing carbon tube L=820mm external diameter 16mm×1 pcs
2# Main wing carbon tube L=760mm external diameter 10mm×1 pcs
Horizontal Stabilizer carbon tube L=650mm external diameter 6mm×1 pcs
Accessories Bag 1 ×1 pcs
Screw (HM3×10mm)×8 pcs (Horizontal tail)
Screw (HA3×10mm)×8 pcs (Vertical tail / Tail nozzle)
Screw (HA3×14mm)×8 pcs (Engine)
Screw (HM3×14mm)×8 pcs (Wing)
Screw (HM4×25mm)×8 pcs (Auxiliary tank)
Screw (PWM6×70mm)×6 pcs (Nose)
Accessories Bag 2 ×1 pcs
100mm signal line(JR male+JR male) ×8 pcs
Manual×1 pcs
REQUIRES:
SW80B 8KG brushless / SW60B 6KG brushless (required & not included)
7 channel radio system (radio & receiver) (required & not included)
2S,7.4V,5200mAh×2,LiPo with XT60 type plug (required & not included)
LiPo battery charger (required & not included)
Pricing and availability subject to change without notice. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$1,549.90Insulating Cloth Adhesive Tape with great abrasion resistance 3/4 X 100ft Good adhesion to multiple surfaces and works great on a wide variety of applications.
$19.99