Use For All Mechanical Mating Parts Metal To Metal - Metal To Plastic Its light viscosity allows it to penetrate quickly and lubricate from within. Its formulation of high quality waxes and PTFE promote friction free operation. Its liquid carrier evaporates and leaves the friction relieving chemistry. It guards against rust and corrosion and it does not attract dirt. Especially good for electronically driven retractable landing gear and mechanical moving parts of pneumatic gear. CAUTON: DO NOT apply to pneumatic cylinders.
$5.50E Bandit Electric Tailpipe Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
Electra "T" and ARF Fuels Cells (1.75 Liters) *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$255.00Electra ARF Main Gear Flex Plates for Robart Landing Gear
$29.95About 3 hours of modeling time and some Aeropoxy are required to make the upgrade. As with any high performance model, it is wise to occasionally disassemble it and check the critical glue joints.
$35.00About 3 hours of modeling time and some Aeropoxy are required to make the upgrade. As with any high performance model, it is wise to occasionally disassemble it and check the critical glue joints.
$35.00Electra Tailpipe - 31.375" length 3.5" exit diameter Thrust Tubes includes laser cut mylar, fittings, plastic tape, and instructions
Engine Strap Screw Clamp 100-105MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00Engine Strap Screw Clamp 105-110MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00Engine Strap Screw Clamp 110-115MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00Engine Strap Screw Clamp 75-80MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00Engine Strap Screw Clamp 80-85MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00Engine Strap Screw Clamp 85-90MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00Engine Strap Screw Clamp 90-95MM Engine Diameter BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00Engine Strap Screw Clamp 95-100MM BVM now offers new Engine Straps for turbine engines. These Engine Strap Screw Clamps are great for all types of engines. The straps are not engine specific and fit a wide range of diameters. NOTE: The Engine Straps and Mounts are sold individually.
$15.00BVM Epoxy Starter Kit includes: Glue Gun, Aeropoxy Cartridge, Vpoxy+ Cartridge, QT Plus Cartridge, (2) 6" Automix nozzles, and (4) 3" Automix nozzles. This BVM Epoxy Glue Starter Kit will introduce you to 3 great Aerospace Grade adhesives that can solve your most challenging assembly tasks. As a manufacture of high performance jet models, we know the importance of strong and long lasting bonds. Aeropoxy, VPoxy+, and QT Plus are used in some of the manufacturing processes of BVM ARF's and are depicted in our assembly manuals. Hobby grade epoxies can deteriorate with time. Aerospace Grade means that when your model is 10+ years old, those critical glue joints will still stand up to high speeds and G's. After you gain experience with this trio of epoxies, you can reorder individual cartridges as necessary.
$98.95EVF ~3~ 10S power unit has been test flown in both the BVM Electra and Sabre Jet with excellent results. It delivers 16Lb of thrust (test cell) at 107 amps and runs very very cool. In-Flight motor temps registered a maximum of 136°F after the most demanding vertical climbs. The Castle Creation's Edge Lite HV160 is housed and kept cool in the EVF's epoxy fiberglass and Kevlar aft fairing for an all up weight of 2Lbs. 3oz. Utilizing ThunderPower 70C 6600 mAh LiPo's (10 cells) we are getting 6+ minute flights without stressing the batteries, i.e. using less than 80% of the capacity.
$1,595.00EVF 9 Blade 12S Fan Unit. An additional 3 Lbs. of thrust is available with the EVF ~3~ 12s system. A larger motor and 2 extra LiPo cells gives us a fan system that will drive a 19-24 Lb. model with convincing jet-like performance. A properly built model in the 19-21 Lb. range that is equipped with landing gear doors (as all BVM jets are) can easily yield 7-8 minutes of flight time on ThunderPower 7700mAh LiPo's.
$1,595.00EVF Shroud and Mounting Hardware We are making the EVF shroud and mounting hardware available for BVM kit builders. This setup will facilitate the placement of inlets and tailpipes in your electric jet model. Simply use the shroud while building, then pop in your EVF when your model is complete and ready for power. There is a $75.00 charge for the shroud, you may return it to BVM for a $50.00 refund. This is a service offered only by BVM.
$75.00AIR OPERATED - SPRING RETURN BVM EZ-DROP simplifies the mounting and releasing of external stores without using a dedicated radio channel or servos. It operates via a single air line from the models retract system. Simply use the snap roll button to command a slight over travel on the retract system valve, and the tanks or bombs release instantly.
$39.95To compliment our pneumatic powered EZ-DROP, we also offer this similar device intended to ease the mounting and removal of external stores by simply pulling aft on the cable. Tanks, bombs and missiles really add to the "presence" and "scale realism" of jet models whether they be on static display or in action at 150 + m.p.h. Handling and transporting the model with external stores however, can be a cumbersome task and sometimes results in damage to fins or pylons. We think you will find the BVM EZ-Hangers a very handy accessory when adding some "parasites" to your jet. EZ-Hangers fit into the same size opening and utilize the same bolt pattern as the EZ-DROPS, they are interchangeable.
$25.95For All Bandits, Electras, 63" Sabres or similar Jet Models. BVM EZ Pylons allows quick attachment and release of external stores without the use of tools. Simply hand operate the bolt head trigger on the side of the pylon. The EZ Drop also allows the release of the stores remotely. Comprehensive manual and drawings are included. This pair of pylons requires the use of either (2) BVM EZ Hanger (BVM#2185) or (2) BVM EZ Drop (BVM#2187) to mount the appropriate wing tanks or ordnance.
$55.00F-1 Mirage PNP Fuel Probe Disclosures: BVM prides itself in providing a quality product delivered to customers on time. Due to the popularity of certain products, we can not guarantee that each item you have ordered will be in stock. If any items you ordered are not in stock, BVM will inform you immediately. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$51.95F-100 Fuel Cells (4.8 Liters) *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$450.00F-16 1:6 LEFT Main Door ONLY - Thunderbird Scheme Hinges Installed
$75.00BVM F-16 1:6 scale PNP Ventral Fins - pair
Disclosures: BVM prides itself in providing a quality product delivered to customers on time. Due to the popularity of certain products, we can not guarantee that each item you have ordered will be in stock. If any items you ordered are not in stock, BVM will inform you immediately. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$69.99BVM F-16 1:6 scale PNP Ventral Fins - pair
Disclosures: BVM prides itself in providing a quality product delivered to customers on time. Due to the popularity of certain products, we can not guarantee that each item you have ordered will be in stock. If any items you ordered are not in stock, BVM will inform you immediately. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$69.99