Originally developed for the BVM 84" Sabre Jet, this Jet-Foam Cradle works well for many medium size jets such as the Bandit, Electra, MiG-15, and F-100. The distance between the End Brackets can be adjusted on the PVC Tubes and the Velcro Straps will hold the model for field assembly, disassembly, and transport, as well as being very handy in the shop while you work on the model. Review the accompanying enclosures and the photos below to see the advantages a BVM Jet-Foam Cradle offers. Modify as desired A razor saw or sharp knife can be used to put a "V" notch in an End Bracket if that best suits your model. Outline the desired modification with tape, then cut. Made in the U.S.A. with BVM Jet-Foam The Jet-Foam Cradle will not scratch or dent your model, but gently hold and "cradle" it while you are working on it in your shop or assembling / disassembling it at the flying field. The Velcro straps are handy for some modeling tasks such as installing the wings and transporting the model in a van or trailer.
$155.00Remove Before Flight. Handling your Kerosene powered model is a lot less messy if you plug off the fuel system overflow vent. You prevent the stinky spills in your vehicle and workshop. But, if you take-off with the vent still plugged, your engine will starve for fuel and flame out, usually one or two minutes into the flight. Unfortunately, this has happened to two customers recently. BVM's "Remove Before Flight" Vent Plug solves the problem. It would be hard to taxi out and not see the Red Flag dragging on the ground.
$11.99Fuel Line Spring Clips - 8MM 10 per package For: Hi-Flow Fuel Systems The 8mm clips can be used on most fittings except those inside the fuel tanks. Safety wire (BVM #2800) is used to secure the flexible tubing to those fittings. Be cautious with the pliers to not pinch the clips more than necessary. Pull test the fuel lines to check for security after the clips are in place.
$7.95Fuel Line Spring Clips - 6MM 10 per package For: Standard Fuel Systems The 6mm clips can be used on most fittings except those inside the fuel tanks. Safety wire (BVM #2800) is used to secure the flexible tubing to those fittings. The standard size clips will secure the 6mm fuel tubing to 5/32” brass tubes as shown. Be cautious with the pliers to not pinch the clips more than necessary. Pull test the fuel lines to check for security after the clips are in place.
$6.95BVM Aluminum Plugs fit our 6mm OD (4mm ID, 5/32") Line. These can be used for Smoke or Fuel Lines. The Aluminum Plug is used after fueling your aircraft. Now available in Purple and Silver to easily identify if it is a fuel or smoke line. Includes: 2 Silver Plugs
$4.99Replacement for PermaGrit #RF9UF (no longer available) How to use: Drill 1/16 pilot hole in the F/G panel. operate this 90 Carbide Rotary Cutter at low RPM. Use a small Phillips Head Driver to install the flush panel screws (BVM # 2155)
$15.95F86 80 Fuel Cells (4.3 Liters) *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$450.00Super Flow Inlet Duct for BVM F-86 63" ARF. In our efforts to constantly improve the efficiency of the BVM EVF powered airframes, we took a close look at the F-86 inlet duct. We found that with some contour changes and the inclusion of a center mounted spike we could gain some performance. The airflow from the nose cone inlet to the fan rotor is now much improved. This is all new tooling and both the static and flight tests confirm the performance increase. It's an easy to install, worthwhile upgrade to an EVF powered F-86. Installing this duct assembly in any existing BVM Sabre designed for EVF or D/F power will yield an additional 1 pound of static thrust. The weight addition is .6 oz.
INCLUDES:
Mylar Thrust Tube, FWD Battery Shelf, Inlet Assembly, Carbon Cord, and hardware
F-86 (60") Tailpipe
F-80/T-33 Kevlar Fuel Cells (2.7 Liters) *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$352.00F-80 Electric Tailpipe
F-4 Fuel Cells (4.1 Liters) *Please Note fuel systems are manufactured per order. Please allow 2 weeks for processing.
$352.00F-4 Electric Tailpipe
The stock springs in all the BVM Go Fly Gold models are already a strong spring for each model.
BVM offers Upgrade Springs for customers that would like a stronger spring tension.
This is not required.
PACKAGE INCLUDES:
2 - .480 X 1.5 Spring
F-18 5.5 Control Arm and Ball Driver for Elevators
$9.99F-18 1:7.75, L-39, Cougar PNP Nose Gear Steering Arm
$9.50F-18 1:7.75 Tail Cone Nozzle Disclosures: BVM prides itself in providing a quality product delivered to customers on time. Due to the popularity of certain products, we can not guarantee that each item you have ordered will be in stock. If any items you ordered are not in stock, BVM will inform you immediately. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$52.50F-18 7.75 Missile Rails painted WHITE Disclosures: BVM prides itself in providing a quality product delivered to customers on time. Due to the popularity of certain products, we can not guarantee that each item you have ordered will be in stock. If any items you ordered are not in stock, BVM will inform you immediately. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$57.50F-18 1:7.75 PNP Missile Rails - Pair
Disclosures: BVM prides itself in providing a quality product delivered to customers on time. Due to the popularity of certain products, we can not guarantee that each item you have ordered will be in stock. If any items you ordered are not in stock, BVM will inform you immediately. If you need an expedited order, please call BVM to verify the stock BEFORE placing the order.
$57.50The stock springs in all the BVM Go Fly Gold models are already a strong spring for each model.
BVM offers Upgrade Springs for customers that would like a stronger spring tension.
This is not required.
PACKAGE INCLUDES:
2 - 16MM X 25MM Spring
2 - Nylon Spacer
F-18 1:5.5 Nose Gear Strut Attachment Pin & Brass Sleeve Assembly
$31.99